4' x 10' Straight Stretch Fabric Zip Stand
4' x 10' Straight Stretch Fabric Zip Stand (Pillow Case Style, Zippered Display)
• Display Size: 48" Wide x 120" High• Fabric Slides over the frame, zippers on bottom.• Sets up in 15 min with 1 person• No Tools Required• Frame Weighs only 8lbs, Fabric about 8lbs• B1 Fire Rated Printed Stretch FabricDetails
Set Up Time - 15min - 1 person, less than 10 min with 2 people
This 4' x 10' display wall can be set up by 1 person although 2 people is preferred. Total set up time for 1 person is about 15 min. Straight pole sections are bungeed together and attach to the corners. Joints are all numbered, so just match the numbers and set up will be quick. Slipping the fabric over the frame is easiest with 2 people working together, but 1 can do it. Once the fabric is over the frame you tension the fabric by zippering the bottom under the bottom bar (easiest if the frame is laying down)
Fabric material and printing process (Pillow Case Style, Zippered Displays)
• These Zippered displays are printed using a dye sublimation process that creates stunning colors and actually dyes the fabric threads. The dye sublimation process produces very high definition prints that last a long time.• The fabric used for this zip stand is a soft knit 5.0 osy polyester material that is crease resistant and has a slight stretch to it, which reduces wrinkles when fully stretched over the tube frame. • FR Rating: NFPA-701 Certified Fire Certificate• The soft look of the fabric makes your booth inviting and if you use it as a step and repeat (or media) backdrop you will not have any glare when taking photos.• Washable - on Cold and air dryAbout the Display Frame
The frame is made of 1-1/4" dia aluminum tube. Very lightweight at about 10lbs. Breaks down into approx 2' sections which are bungee corded together for easy setup. Sections snap together with snap pins. No tools are needed to erect this frame and it would take 1 person less than 10 minutes to assemble. All the joints are numbered for easy assembly, simply match up the numbers and you will be done in no time.
About the Lights
Lights are 18w LEDs on an arm that sticks out from the frame. The lights are attached to a clamp on the bar of the frame. Typically you would want at least 2 lights on this 4' frame. This frame type is difficult to add lights to both sides if you have a double-sided graphic since there is really no place to run the wires along the top of the display.
About the Hard Carry Case Option
The Small Hard Case is a molded plastic hard carry case with a center handle grip and inset wheels for easy mobility.
more about the hard carry case
Shipping Sizes
Hardware Only w/soft case - 35" x 8" x 7" 14lbs. (box size - 34.5x13x6.5)
Hardware, Fabric (2.8 lbs.), and shipping box - 34.5x13x6.5 16.8 lbs.
Shipping - Need it Faster?
We have an option to get your project to print faster than our normal turnaround. How it works - Once you approve your proof we will put you on a 24hr print path, which means we will get your project ready to ship within 24hrs.
Setup Instructions
Link for full Installation Instructions
Assemble the frame - Less the feet.
Pull the fabric over the frame and pull on the sides evenly.
They may catch a bit on the tube joints, just pull the fabric out and over to continue. Once the fabric is on the frame it is easiest to lay the frame down to zip the fabric under the bottom tube.
Zipping the fabric
Find the end where the zipper is to start.
Grab both sides of the fabric and pull around the bottom tube of the frame. This stretches the fabric and makes it easier to set the zipper.
Start the zipper and zip it across the bottom of the stand, pulling the fabric down if need be.
Feet
Add the feet to your Zip Stand and stand it up.
Adjustments: These tube frames can be easily adjusted if there is a twist to the frame after the fabric is on. Simply twist the frame until it is flat. The tension of the fabric will hold it where you set it.
Design Templates
4' x 10' Stretch Fabric Zip Stand Display 1-1/4" Tube
• Page Size with Bleed - 50” wide x 120” high • Actual graphics area of the frame size is 48” wide x 117.5”• Press PDF, JPG, or EPS files are preferred, with text converted to outlines or curves.• CMYK color space is best, RGB works ok.• Image resolution should be approx 125dpi at final size for best printing.• Large files should be uploaded after the order is placed using the "File Upload" tab at the top of the website. 4'x10' Zip Stand Design Template - to save this file to your computer, simply right click and "save link as".How to order with multiple or large files
• Place your order for the total number of stretch fabric display stands you want and check out.• After you place your order, go to our "File Upload" tab located on the top of the home page. There you can upload up to 6 files at a time, if you have more than 6 , simply send another set.• We connect your order and your files by the email you use on your order and the file upload. If we have any questions we will let you know.• We will be in contact with you on all orders before we go to print.Reviews
Link for full Installation Instructions
Assemble the frame - Less the feet.
Pull the fabric over the frame and pull on the sides evenly.
They may catch a bit on the tube joints, just pull the fabric out and over to continue. Once the fabric is on the frame it is easiest to lay the frame down to zip the fabric under the bottom tube.
Zipping the fabric
Find the end where the zipper is to start.
Grab both sides of the fabric and pull around the bottom tube of the frame. This stretches the fabric and makes it easier to set the zipper.
Start the zipper and zip it across the bottom of the stand, pulling the fabric down if need be.
Feet
Add the feet to your Zip Stand and stand it up.
Adjustments: These tube frames can be easily adjusted if there is a twist to the frame after the fabric is on. Simply twist the frame until it is flat. The tension of the fabric will hold it where you set it.